Install/MBR Partitioning/pt-br

Guia de Instalação: Particionamento MBR

Install Guide, Chapter 3

< Prev

Next >

Método Legado (BIOS/MBR)

   Note

Use this method if you are booting using your BIOS, and if your System Rescue CD initial boot menu was light blue. If you're going to use the UEFI/GPT disk format, then please proceed to the next section.

First, it's a good idea to make sure that you've found the correct hard disk to partition. Try this command and verify that /dev/sda is the disk that you want to partition:

root # fdisk -l /dev/sda

Disk /dev/sda: 640.1 GB, 640135028736 bytes, 1250263728 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: gpt

root #         Start          End    Size  Type            Name
 1         2048   1250263694  596.2G  Linux filesyste Linux filesystem

Now, it is recommended that you erase any existing MBR or GPT partition tables on the disk, which could confuse the system's BIOS at boot time. We accomplish this using sgdisk:

   Warning

This will make any existing partitions inaccessible! You are strongly cautioned and advised to backup any critical data before proceeding.

root # sgdisk --zap-all /dev/sda

Creating new GPT entries.
GPT data structures destroyed! You may now partition the disk using fdisk or
other utilities.

This output is also nothing to worry about, as the command still succeeded:

***************************************************************
Found invalid GPT and valid MBR; converting MBR to GPT format
in memory. 
***************************************************************

Now we will use fdisk to create the MBR partition table and partitions:

root # fdisk /dev/sda

Within fdisk, follow these steps:

Empty the partition table:

Command (m for help): o ↵

Create Partition 1 (boot):

Command (m for help): n ↵
Partition type (default p): ↵
Partition number (1-4, default 1): ↵
First sector: ↵
Last sector: +128M ↵

Create Partition 2 (swap):

Command (m for help): n ↵
Partition type (default p): ↵
Partition number (2-4, default 2): ↵
First sector: ↵
Last sector: +2G ↵
Command (m for help): t ↵ 
Partition number (1,2, default 2):  ↵
Hex code (type L to list all codes): 82 ↵

Create the root partition:

Command (m for help): n ↵
Partition type (default p): ↵
Partition number (3,4, default 3): ↵
First sector: ↵
Last sector: ↵

Verify the partition table:

Command (m for help): p

Disk /dev/sda: 298.1 GiB, 320072933376 bytes, 625142448 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0x82abc9a6

Device    Boot     Start       End    Blocks  Id System
/dev/sda1           2048    264191    131072  83 Linux
/dev/sda2         264192   4458495   2097152  82 Linux swap / Solaris
/dev/sda3        4458496 625142447 310341976  83 Linux

Write the partition table to disk:

Command (m for help): w

Your new MBR partition table will now be written to your system disk.

   Note

You're done with partitioning! Now, jump over to Creating filesystems.