Make.conf

Subpages:

VIDEO_CARDS

What is the make.conf file?

Make.conf is portage's and Funtoo's main configuration file. It contains many variables that define how a package will be installed in a Funtoo system. You can customize portage internal variables, such as, portage tree location, sources tarball location, overlays, to name a few. You can customize hardware specs, such as TMPFS, disk limits, GCC compilation flags to achieve best performance, etc. A great deal of this customization is done through the make.conf file. This page will attempt to explain the uses of the make.conf file, different variables that can be added to it, and their uses.

Where is make.conf located?

make.conf is located in /etc and is a symbolic link to /etc/portage/make.conf, so these filenames are used interchangeably (though drobbins prefers using /etc/make.conf since it's shorter to type so you'll see this filename used more often in the docs.)

No special tool is required to edit /etc/make.conf, besides your favorite text editor, of course:

root # nano /etc/make.conf

Variables

Portage is very cutomizable. Because of this, many variables are available to configure /etc/make.conf. Below is an example make.conf file showing some of the variables that can be used to customize portage. The format of a line of this file is usually VARIABLENAME="variable arguments".

   /etc/make.conf - example make.conf variables

CFLAGS="-march=amdfam10 -O2 -pipe"
CXXFLAGS="-march=amdfam10 -O2 -pipe"
INPUT_DEVICES="evdev"
VIDEO_CARDS="vesa nouveau"
MAKEOPTS="-j2"
USE="mmx sse"
ACCEPT_LICENSE="*"

   Note

This isn't a great example of a make.conf file in Funtoo, because on nearly all systems the variables CFLAGS, CXXFLAGS, etc are set using profile subarch mix-ins rather than manually in /etc/make.conf. Portage also has a built-in check for CPU's cores and enables MAKEOPTS automatically, if not set. In make.conf you may increase or decrease the value, when needed, otherwise it's set to -j(core number)

Below is a list of variables that can be used in make.conf, along with a description of what they do. For more information on these and other variables, see the subpages list at the top of this page and/or read man make.conf.

Accept All Licenses

   /etc/portage/make.conf - accept all licenses

ACCEPT_LICENSE="*"

Relocate Source Compile Directory

By default portage unpacks and compiles sources in /var/tmp/ it appends portage/pkg-cat/pkg to compile a package elsewhere. For example, if portage compiles a package in /tmp, it will be built at: /tmp/portage/pkg-cat/pkg. If you have Funtoo installed on an SSD, it may be a wise decision to mount /tmp in RAM or on a HDD so that you can minimize the number of writes to your SSD and extend its lifetime. After /tmp has been mounted off of your SSD, you can tell portage to compile future packages in /tmp, instead of in /var/tmp. To do this, add the following line to your /etc/portage/make.conf:

   /etc/portage/make.conf

PORTAGE_TMPDIR="/tmp"

Video_Cards

The VIDEO_CARDS variable tells portage which video drivers you wish to use on your system. To see the different options that exist for this variable, see Video.

Laptop Mice

See x11-drivers/xf86-input-synaptics for laptop mice & touch pads.

MAKEOPTS

MAKEOPTS can be used to define how many parallel compilations should occur when you compile a package, which can speed up compilation significantly. By default, this variable is set to the number of cores (or CPU threads) in your system plus one. If for example you have a dual core processor without hyper-threading, then MAKEOPTS would be set to 3, which could be done manually as follows:

   /etc/portage/make.conf - set portage to use 3 threads

MAKEOPTS="-j3"

If you are unsure about how many processors/threads you have then use /proc/cpuinfo to help you.

(chroot) # grep "processor" /proc/cpuinfo

USE flags

USE flags define what functionality is enabled when packages are built. It is not recommended to add a lot of them during installation; you should leverage Funtoo Profiles instead as much as possible and only set as needed. A USE flag prefixed with a minus (" - ") sign tells Portage not to use the flag when compiling. Through use flags we generate more secure stripped down binaries with reduced attack surface and better performance. A Funtoo guide to USE flags will be available in the future. For now, you can find out more information about USE flags in the Gentoo Handbook.

Input

Some devices need defined such as x11-drivers/xf86-input-synaptics for touch pads.

   /etc/portage/make.conf - synaptics example

INPUT_DEVICES="synaptics evdev"

Localization

Available options can be found on Funtoo Linux Localization.