The Funtoo Linux project has transitioned to "Hobby Mode" and this wiki is now read-only.
Difference between revisions of "Install/Chroot/pl"
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 8: | Line 8: | ||
</div> | </div> | ||
<div class="mw-translate-fuzzy"> | |||
Żeby zainstalować Funtoo, najpierw używamy {{c|chroot}}. Polecenie "przełącza" na nowy system Funtoo Linux. Wpisywane odtąd komendy będą uruchomiać się na nowo rozpakowanym systemie. | Żeby zainstalować Funtoo, najpierw używamy {{c|chroot}}. Polecenie "przełącza" na nowy system Funtoo Linux. Wpisywane odtąd komendy będą uruchomiać się na nowo rozpakowanym systemie. | ||
</div> | |||
<div lang="en" dir="ltr" class="mw-content-ltr"> | |||
{{console|body= | |||
# ##i##fchroot /mnt/funtoo | |||
%fchroot% | |||
}} | |||
</div> | |||
<div lang="en" dir="ltr" class="mw-content-ltr"> | |||
The {{c|fchroot}} command will take care of all necessary steps to enter into your new Funtoo Linux system, as well as clean up things when you exit the fchroot by typing | |||
{{c|exit}} or {{c|ctrl-D}}. | |||
</div> | |||
<div lang="en" dir="ltr" class="mw-content-ltr"> | |||
If you are using another LiveCD or USB media to install Funtoo, you can manually chroot by using the following set of commands: | |||
</div> | |||
<div class="mw-translate-fuzzy"> | <div class="mw-translate-fuzzy"> | ||
| Line 18: | Line 36: | ||
# ##i##mount --rbind /dev dev | # ##i##mount --rbind /dev dev | ||
}} | }} | ||
</div> | </div> | ||
| Line 37: | Line 44: | ||
<div lang="en" dir="ltr" class="mw-content-ltr"> | <div lang="en" dir="ltr" class="mw-content-ltr"> | ||
Test internet name resolution from within the chroot: | Test internet name resolution from within the chroot: | ||
{{console|body=%chroot% ##i##ping -c 5 google.com}} | {{console|body=%chroot% ##i##ping -c 5 google.com}} | ||
Latest revision as of 00:59, May 26, 2023
Przewodnik Instalacji: 'chroot' do nowego systemu
Żeby zainstalować Funtoo, najpierw używamy chroot. Polecenie "przełącza" na nowy system Funtoo Linux. Wpisywane odtąd komendy będą uruchomiać się na nowo rozpakowanym systemie.
root # fchroot /mnt/funtoo fchroot #
The fchroot command will take care of all necessary steps to enter into your new Funtoo Linux system, as well as clean up things when you exit the fchroot by typing
exit or ctrl-D.
If you are using another LiveCD or USB media to install Funtoo, you can manually chroot by using the following set of commands:
Przed 'chroot'owaniem, należy wykonać kilka czynności aby skonfigurować środowisko 'chroot'. Trzeba będzie zamontować /proc, /sys oraz /dev wewnątrz nowego systemu. Aby to zrobić, użyj następujących poleceń:
root # cd /mnt/funtoo root # mount -t proc none proc root # mount --rbind /sys sys root # mount --rbind /dev dev
For users of live CDs with 64-bit kernels installing 32-bit systems: Some software may use uname -r to check whether the system is 32 or 64-bit. You may want to append linux32 to the chroot command as a workaround, but it's generally not needed.
If you receive the error "chroot: failed to run command `/bin/bash': Exec format error", it is most likely because you are running a 32-bit kernel and trying to execute 64-bit code. Make sure that you have selected the proper type of kernel when booting your live CD.
Test internet name resolution from within the chroot:
chroot # ping -c 5 google.com
If you can't ping, make sure that /etc/resolv.conf specifies a valid IP address for a reachable nameserver in its nameserver setting.
Congratulations! You are now chrooted inside a Funtoo Linux system. Now it's time to get Funtoo Linux properly configured so that Funtoo Linux will start successfully, without any manual assistance, when your system is restarted.
| Install Guide, Chapter 9 | < Prev | Next > |