The Funtoo Linux project has transitioned to "Hobby Mode" and this wiki is now read-only.
Difference between revisions of "Install/GPT Partitioning/en"
(Updating to match new version of source page) |
(Updating to match new version of source page) |
||
| Line 8: | Line 8: | ||
==== UEFI/GPT Method ==== | ==== UEFI/GPT Method ==== | ||
{{Note|Use this method if you are interested in booting using UEFI, and if your System Rescue CD initial boot menu was black and white. If it was light blue, this method will not work. Instead, use the instructions in the previous section, or reboot SystemRescueCD in UEFI mode first.}} | {{Note|Use this method if you are interested in booting using UEFI, and if your System Rescue CD initial boot menu was black and white. If it was light blue, this method will not work. Instead, use the instructions in the previous section then skip this section, or reboot SystemRescueCD in UEFI mode first.}} | ||
The {{c|gdisk}} commands to create a GPT partition table are as follows. Adapt sizes as necessary, although these defaults will work for most users. Start {{c|gdisk}}: | The {{c|gdisk}} commands to create a GPT partition table are as follows. Adapt sizes as necessary, although these defaults will work for most users. Start {{c|gdisk}}: | ||
| Line 69: | Line 69: | ||
{{Tip|You can verify that the block devices above were correctly created by running the command {{c|lsblk}}.}} | {{Tip|You can verify that the block devices above were correctly created by running the command {{c|lsblk}}.}} | ||
<noinclude>{{InstallNavigation|num=4|prev=MBR Partitioning|next=Creating Filesystems|align=right}}</noinclude> | |||
Revision as of 22:08, October 10, 2019
Install Guide: GPT Partitioning
| Install Guide, Chapter 4 | < Prev | Next > |
UEFI/GPT Method
Use this method if you are interested in booting using UEFI, and if your System Rescue CD initial boot menu was black and white. If it was light blue, this method will not work. Instead, use the instructions in the previous section then skip this section, or reboot SystemRescueCD in UEFI mode first.
The gdisk commands to create a GPT partition table are as follows. Adapt sizes as necessary, although these defaults will work for most users. Start gdisk:
root # gdisk /dev/sda
Within gdisk, follow these steps:
Create a new empty partition table (This will erase all data on the disk when saved):
Command: o ↵ This option deletes all partitions and creates a new protective MBR. Proceed? (Y/N): y ↵
Create Partition 1 (boot):
Command: n ↵ Partition Number: 1 ↵ First sector: ↵ Last sector: +500M ↵ Hex Code: EF00 ↵
Create Partition 2 (swap):
Command: n ↵ Partition Number: 2 ↵ First sector: ↵ Last sector: +4G ↵ Hex Code: 8200 ↵
Create Partition 3 (root):
Command: n ↵ Partition Number: 3 ↵ First sector: ↵ Last sector: ↵ (for rest of disk) Hex Code: ↵
Along the way, you can type "p" and hit Enter to view your current partition table. If you make a mistake, you can type "d" to delete an existing partition that you created. When you are satisfied with your partition setup, type "w" to write your configuration to disk:
Write Partition Table To Disk:
Command: w ↵ Do you want to proceed? (Y/N): Y ↵
The partition table will now be written to the disk and gdisk will close.
Now, your GPT/GUID partitions have been created, and will show up as the following block devices under Linux:
/dev/sda1, which will be used to hold the/bootfilesystem,/dev/sda2, which will be used for swap space, and/dev/sda3, which will hold your root filesystem.
You can verify that the block devices above were correctly created by running the command lsblk.
| Install Guide, Chapter 4 | < Prev | Next > |