注意：
The Funtoo Linux project has transitioned to "Hobby Mode" and this wiki is now read-only.
Difference between revisions of "SiFive Freedom U740"
Jump to navigation
Jump to search
| Line 7: | Line 7: | ||
|Description=This subarch supports the RISC-V SiFive Freedom U740 processor, featured on the [https://www.sifive.com/boards/hifive-unmatched HiFive Unmatched] board. | |Description=This subarch supports the RISC-V SiFive Freedom U740 processor, featured on the [https://www.sifive.com/boards/hifive-unmatched HiFive Unmatched] board. | ||
}} | }} | ||
== What you need == | |||
* The [https://www.sifive.com/boards/hifive-unmatched Hifive Unmatched], with an M.2 disk and a GPU installed (see the [https://sifive.cdn.prismic.io/sifive/65937c64-c6ca-4bc7-80d1-e830a895636a_hifive-unmatched-getting-started-guide-v1p4.pdf Getting started guide] about qualified options) | |||
* A microSD card loaded with the [https://github.com/sifive/freedom-u-sdk Freedom U SDK], preferably the CLI version (for example using [https://github.com/sifive/freedom-u-sdk/releases/download/2022.04.00/demo-coreip-cli-unmatched-2022.04.00.rootfs.wic.xz this] disk image). | |||
== Installation == | |||
* Insert the prepared microSD card and boot into the Linux loaded on it. | |||
* Follow the usual [https://www.funtoo.org/Install/Introduction Funtoo installation process] to prepare the M.2 disk ({{c|/dev/nvme0n1}}), but don't create a separate boot partition, as you're going to be using the one already present on the microSD card ({{c|/dev/mmcblk0p3}}). | |||
* Mount your partitions under {{c|/mnt/funtoo}}, it should look similar to this (ignore additional rows): | |||
{{console|body= | |||
###i## lsblk | |||
mmcblk0 179:0 0 30G 0 disk | |||
|-mmcblk0p1 179:1 0 1M 0 part | |||
|-mmcblk0p2 179:2 0 4M 0 part | |||
|-mmcblk0p3 179:3 0 130M 0 part /mnt/funtoo/boot | |||
`-mmcblk0p4 179:4 0 6.5G 0 part | |||
nvme0n1 259:0 0 931.5G 0 disk | |||
`-nvme0n1p1 259:1 0 931.5G 0 part /mnt/funtoo | |||
}} | |||
* Finish the usual normal Funtoo installation until you need to configure booting (remember to add the microSD card boot partition to your {{c|fstab}} | |||
* Add Funtoo to the U-Boot config on the microSD card: | |||
{{file|name=/mnt/funtoo/boot/extlinux/extlinux.conf|body= | |||
default Funtoo | |||
label OpenEmbedded-SiFive-HiFive-Unmatched | |||
kernel /Image.gz-initramfs-unmatched.bin | |||
fdt /hifive-unmatched-a00.dtb | |||
append root=/dev/mmcblk0p4 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon | |||
label Funtoo | |||
kernel /Image.gz-initramfs-unmatched.bin | |||
fdt /hifive-unmatched-a00.dtb | |||
append root=/dev/nvme0n1p1 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon | |||
}} | |||
* Rebooting should load your Funtoo installation with the official Freedom U SDK kernel | |||
{{note|'''Self-compiled kernel''': Build the kernel into a single (EFI) image (with an embedded initramfs, should you need one), then install that to the microSD card's boot partition, along with the {{c|hifive-unmatched-a00.dtb}} file from your kernel's source directory. Adjust the {{c|kernel}} and {{c|fdt}} entries from {{c|/boot/extlinux/extlinux.conf}} accordingly.}} | |||
Revision as of 10:10, June 5, 2022
This section lists the CPU-optimized Funtoo Linux builds currently available for download for sifive-fu740. This subarch supports the RISC-V SiFive Freedom U740 processor, featured on the HiFive Unmatched board.
next
Not sure which to choose? See this portion of our Install docs.
For information on how to verify the integrity of your stage3 tarball using gpg, see GPG Signatures.
Downloads accelerated by 
Architecture and Optimization
The following settings are applied to all stages for this subarch via Funtoo subarch profiles:
| CHOST | riscv64-unknown-linux-gnu |
| CFLAGS | -O2 -march=rv64gc -mabi=lp64d |
What you need
- The Hifive Unmatched, with an M.2 disk and a GPU installed (see the Getting started guide about qualified options)
- A microSD card loaded with the Freedom U SDK, preferably the CLI version (for example using this disk image).
Installation
- Insert the prepared microSD card and boot into the Linux loaded on it.
- Follow the usual Funtoo installation process to prepare the M.2 disk (
/dev/nvme0n1), but don't create a separate boot partition, as you're going to be using the one already present on the microSD card (/dev/mmcblk0p3). - Mount your partitions under
/mnt/funtoo, it should look similar to this (ignore additional rows):
root # lsblk mmcblk0 179:0 0 30G 0 disk
- Finish the usual normal Funtoo installation until you need to configure booting (remember to add the microSD card boot partition to your
fstab - Add Funtoo to the U-Boot config on the microSD card:
/mnt/funtoo/boot/extlinux/extlinux.conf default Funtoo
label OpenEmbedded-SiFive-HiFive-Unmatched
kernel /Image.gz-initramfs-unmatched.bin
fdt /hifive-unmatched-a00.dtb
append root=/dev/mmcblk0p4 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon
label Funtoo
kernel /Image.gz-initramfs-unmatched.bin
fdt /hifive-unmatched-a00.dtb
append root=/dev/nvme0n1p1 rootfstype=ext4 rootwait console=ttySIF0,115200 earlycon
- Rebooting should load your Funtoo installation with the official Freedom U SDK kernel
Note
Self-compiled kernel: Build the kernel into a single (EFI) image (with an embedded initramfs, should you need one), then install that to the microSD card's boot partition, along with the hifive-unmatched-a00.dtb file from your kernel's source directory. Adjust the kernel and fdt entries from /boot/extlinux/extlinux.conf accordingly.