Funtoo on the Nvidia TK1

Introduction

Read this.

And this

And this.

And this

Getting the Sources

Use the tools issued by Nvidia to handle kernel sources via git. Checkout the desired kernel version, which probably should match the version of the driver package (RXX-X), update the environment variables and create a branch named by the kernel version.

root # wget http://developer.nvidia.com/embedded/dlc/l4t-Jetson-TK1-Driver-Package-R21-5 -O $TOOLS/l4t-Jetson-TK1-Driver-Package-R21-5
root # cd $TOOLS
root # tar jxf l4t-Jetson-TK1-Driver-Package-R21-5
root # rm l4t-Jetson-TK1-Driver-Package-R21-5
root # cd Linux_for_Tegra
root # ./source_sync.sh  #skip tag selection both times
root # cd sources/kernel_source
root # git ls-remote
root # git checkout tegra-l4t-r21.5
root # ln -s $PWD $XC_KERNEL_SRC
root # . xcompile_variables.sh
root # git checkout -b `get_kernel_version`

Kernel Building

You need a working kernel config. You can get one from a running TK1 and get it into your $XC_KERNEL_SRC directory.

root # zcat /proc/config.gz > my_TK1_config
root # scp my_TK1_config <xc_user>@<xc_host>:~
root # cp ~/my_TK1_config $CONFIGS/`get_kernel_version`.kconf

Or you can get it from the kernel headers.

root # cd $TOOLS/Linux_for_Tegra/kernel
root # tar xvf kernel_headers.tbz2
root # cp linux-headers-<kernel_version>/.config $CONFIGS/`get_kernel_version`.kconf

Make the Kernel

root # . xcompile_variables.sh
root # cd $XC_KERNEL_SRC
root # cp $XC_KERNEL_OLDCONFIG .config
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- make oldconfig
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- make zImage modules dtbs

Download and Configure Stage3

See http://www.funtoo.org/Crossdev_Automation#Stage3_Configuration

Don't configure fstab and leave a serial console configured on ttyS2 in $XC_STAGES/etc/inittab.

root # echo "# UNCONFIGURED FSTAB FOR BASE SYSTEM" > $XC_STAGE3S/fstab

Install Super Special Blobs

Make a link to our stage 3 and copy over nvidia binaries to it.

root # cd $TOOLS/Linux_for_Tegra
root # rmdir rootfs
root # ln -s $XC_STAGE3S rootfs
root # ./apply_binaries.sh

Copy over Everything

root # cd $XC_KERNEL_SRC
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- INSTALL_MOD_PATH=$XC_STAGE3S INSTALL_MOD_STRIP=1 make modules_install
root # ARCH=$ARCH CROSS_COMPILE=$CROSSDEV_TARGET- INSTALL_MOD_PATH=$XC_STAGE3S make firmware_install
root # rsync -avz $XC_FIRMWARE/ $XC_STAGE3S/lib/firmware
root # rsync -avz arch/arm/boot/zImage $XC_STAGE3S/boot
root # rsync -avz arch/arm/boot/dts/*.dtb $XC_STAGE3S/boot
root # rm $XC_STAGE3S/lib/modules/`get_kernel_release`/{build,source}

Flash the TK1

Put your system into “reset recovery mode” by holding down the “RECOVERY” button and press “RESET” button once on the main board.

Ensure your Linux host system is connected to the target device through the USB cable for flashing.

root # lsusb | grep -i nvidia
Bus 003 Device 002: ID 0955:7140 NVidia Corp.

Try flashing the kernel first to the partition id LNX. Cross your fingers.

root # cd $TOOLS/Linux_for_Tegra
root #./flash.sh -k LNX -L bootloader/fastboot.bin -K $XC_KERNEL_SRC/arch/arm/boot/zImage jetson-tk1 mmcblk0p1
copying bctfile(/usr/src/fun_kernel/tools/TK1/Linux_for_Tegra/bootloader/ardbeg/BCT/PM375_Hynix_2GB_H5TC4G63AFR_H5TC4G63CFR_RDA_924MHz.cfg)... done.
Existing bootloader(/usr/src/fun_kernel/tools/TK1/Linux_for_Tegra/bootloader/fastboot.bin) reused.
making zero initrd... 
done.
Making Boot image... done.
Making system.img... 
	populating rootfs from /mnt/Workspace/Jetson/21-5/Linux_for_Tegra/rootfs ... done.
	Sync'ing system.img ... done.
	Converting RAW image to Sparse image... 

---- Raw to Sparse Image Converter v1.0 ----------------------------
  0: RAW:     4231168(   1033 blks) ==>          28:4231180
  1: SKP:       40960(     10 blks) ==>     4231208:40972
  2: RAW:        4096(      1 blks) ==>     4231220:4108
...<lots o output>...

Time taken for flashing 4 Secs
*** The 6:LNX has been updated successfully. ***

Now flash the root file system.

root #  ./flash.sh -S 8GiB -L bootloader/fastboot.bin jetson-tk1 mmcblk0p1
copying bctfile(/usr/src/fun_kernel/tools/TK1/Linux_for_Tegra/bootloader/ardbeg/BCT/PM375_Hynix_2GB_H5TC4G63AFR_H5TC4G63CFR_RDA_924MHz.cfg)... done.
Existing bootloader(/usr/src/fun_kernel/tools/TK1/Linux_for_Tegra/bootloader/fastboot.bin) reused.
making zero initrd... 
done.
Making Boot image... done.
Making system.img... 
	populating rootfs from /usr/src/fun_kernel/stage3s/TK1/funtoo-current/arm-32bit/armv7a_neonvfpv4_hardfp ... done.
	Sync'ing system.img ... done.
	Converting RAW image to Sparse image... 

---- Raw to Sparse Image Converter v1.0 ----------------------------
  0: RAW:     4214784(   1029 blks) ==>          28:4214796
  1: SKP:       49152(     12 blks) ==>     4214824:49164
  2: RAW:        8192(      2 blks) ==>     4214836:8204
...<lots of output>...
Create, format and download  took 91 Secs
Time taken for flashing 95 Secs
*** The target ardbeg has been flashed successfully. ***
Reset the board to boot from internal eMMC.