The Funtoo Linux project has transitioned to "Hobby Mode" and this wiki is now read-only.
Install/Creating Filesystems/pl
Przewodnik Instalacji: Tworzenie systemu plików
| Install Guide, Chapter 5 | < Prev | Next > |
Ten rozdział zawiera instrukcję instalacji dla obydwu formatów dysku: MBR oraz GPT/UEFI. Nie omijaj go!
Przed użyciem nowo utworzonych (w poprzednim rozdziale) partycji muszą być one zainicjowane. Ten proces nazwany jest tworzeniem systemu plików na urządzeniach blokowych. Po utworzeniu metadanych systemu plików na partycjach, można je zamontować i wykorzystać do przechowywania informacji.
Zróbmy to najprościej. Czy korzystasz ze starszego typu tablicy partycji MBR? Jeśli tak, stwórzmy system plików ext4 na /dev/sda1:
root # mkfs.ext4 /dev/sda1
Jeśli używasz partycji GPT dla UEFI lub instalujesz system dla Raspberry Pi, będziesz chciał utworzyć system plików vfat na pierwszej partycji (w przypadku Raspberry Pi będzie to mmcblk0p1):
root # mkfs.vfat -F 32 /dev/sda1
Teraz zainicjujmy partycję wymiany. Ta partycja będzie używana jako pamięć wirtualna dla Twojego systemu Funtoo Linux.
You will not create a filesystem on your swap partition, since it is not used to store files. But it is necessary to initialize it using the mkswap command. Then we'll run the swapon command to make your newly-initialized swap space immediately active within the live CD environment, in case it is needed during the rest of the install process:
root # mkswap /dev/sda2 root # swapon /dev/sda2
Root Filesystem
Now, we need to create a root filesystem. This is where Funtoo Linux will live. We generally recommend ext4 or XFS root filesystems.
Keep in mind that some filesystems will require additional filesystem tools to be emerged prior to rebooting. Please consult the following table for more information:
| Filesystem | Recommended as root file system? | Additional tools required to emerge |
|---|---|---|
| ext4 | Yes | None |
| XFS | Yes | sys-fs/xfsprogs |
| reiserfs | Yes -- will likely need to enable kernel support | sys-fs/reiserfsprogs |
| zfs | No - advanced users only | sys-fs/zfs |
| btrfs | No - advanced users only | sys-fs/btrfs-progs |
We do not recommend users set up ZFS or BTRFS as their root filesystem. This is much more complex and usually not necessary. Instead, choose XFS or ext4. We do support ZFS or BTRFS as non-root filesystems and this is much, much easier to configure. See ZFS and BTRFS after you are done setting up your Funtoo Linux system to configure ZFS or BTRFS for additional secondary storage.
If you're not sure, choose ext4. Here's how to create a root ext4 filesystem:
root # mkfs.ext4 /dev/sda3
...and here's how to create an XFS root filesystem, if you prefer to use XFS instead of ext4:
root # mkfs.xfs /dev/sda3
Your filesystems (and swap) have all now been initialized, so that that can be mounted (attached to your existing directory heirarchy) and used to store files. We are ready to begin installing Funtoo Linux on these brand-new filesystems.
Additional Filesystems
This can be very useful for Raspberry Pi systems!
You may want to create additional filesystems for various parts of your Funtoo filesystem tree. It is not uncommon to place /home or /var on separate filesystems.
For Raspberry Pi, you may not have a lot of spare room on the card depending on the capacity of your microSD card, and it may make a lot of sense to put the entire /var filesystem on an external hard drive or solid state disk. This will not only ensure you don't run out of disk space, but can also improve performance since writes to the microSD card typically aren't that fast.
To do this, you will want to use fdisk or gdisk to create a partition on your external drive, and then use the mkfs.xfs or mkfs.ext4 commands to create a filesystem on the new partition. We will mount this new filesystem in the next step prior to extracting the stage3 tarball.
| Install Guide, Chapter 5 | < Prev | Next > |