Kurulum Kılavuzu: Önyükleyici

Install Guide, Chapter 14

boot.conf Configuration

Bu sayfa, BIOS (legacy) veya UEFI kullanarak önyükleme yapmak için GRUB'un nasıl ayarlanması gerektiğini gösterir.

ego boot update (ego boot) is installed by default, but GRUB is not, as it is not required for all Funtoo Linux systems (such as containers, for example.) But for booting on bare metal, it is the recommended and best-supported boot loader, so you will need to emerge it:

(chroot) # emerge -av grub

boot.conf

/etc/boot.conf controls boot loader configuration in Funtoo. Here is what is in the file by default:

/etc/boot.conf

boot {
	generate grub
	default "Funtoo Linux"
	timeout 3
}

"Funtoo Linux" {
	kernel kernel[-v]
	initrd initramfs[-v]
	params += real_root=auto rootfstype=auto
}

"Funtoo Linux (nomodeset)" {
	kernel kernel[-v]
	initrd initramfs[-v]
	params += real_root=auto rootfstype=auto nomodeset
}

If you are booting a custom or non-default kernel, please read man boot.conf for information on the various options available to you.

nomodeset

You will notice after booting that you there will be a boot option in the GRUB menu for a "nomodeset" mode. We don't recommend you use this mode by default but it is available to you for a couple of good reasons:

For users with HiDPI (4K+) displays, especially laptops: If you have not set up a graphical environment, when the kernel automatically changes graphics modes, the console font can be tiny and unreadable.
For users with incompatible graphics cards: Some graphics cards don't handle mode setting properly and this can result in a blank screen after reboot. Use this boot option as a temporary workaround.

To use the nomodeset option, simply select that option from the GRUB menu when your system boots.

rootwait

If you are using a root partition on an nvme device, add the rootwait kernel parameter to force the kernel to wait for it to asynchronously initialize or the kernel will panic on some hardware.

Intel Microcode

ego boot will ensure that you have the most recent Intel CPU microcode installed on your system if you emerge the following packages:

chroot # emerge intel-microcode iucode_tool

This is not necessary for AMD systems.

Old School (BIOS) MBR

When using "old school" BIOS booting, run the following command to install GRUB to your MBR, and generate the /boot/grub/grub.cfg configuration file that GRUB will use for booting:

chroot # grub-install --target=i386-pc --no-floppy /dev/sdX
chroot # ego boot update

New School (UEFI) Boot Entry

If you're using "new school" UEFI booting, run of the following sets of commands, depending on whether you are installing a 64-bit or 32-bit system. This will add GRUB as a UEFI boot entry.

For x86-64bit systems:

chroot # mount -o remount,rw /sys/firmware/efi/efivars
chroot # grub-install --target=x86_64-efi --efi-directory=/boot --bootloader-id="Funtoo Linux [GRUB]" --recheck /dev/sda
chroot # ego boot update

For x86-32bit systems:

chroot # mount -o remount,rw /sys/firmware/efi/efivars
chroot # grub-install --target=i386-efi --efi-directory=/boot --bootloader-id="Funtoo Linux [GRUB]" --recheck /dev/sda
chroot # ego boot update

First Boot, and in the future...

OK -- you are almost ready to boot!

You only need to run grub-install when you first install Funtoo Linux, but you need to re-run ego boot update every time you modify your /etc/boot.conf file or add new kernels to your system. This will regenerate /boot/grub/grub.cfg so that you will have new kernels available in your GRUB boot menu upon your next reboot.

Post reboot UEFI troubleshooting

In case UEFI NVRAM boot entry is missing in BIOS and grub does not start you can try moving an already installed GRUB EFI executable to the default/fallback path

chroot # mv -v '/boot/EFI/Funtoo Linux [GRUB]' /boot/EFI/BOOT
chroot # mv -v /boot/EFI/BOOT/grubx64.efi /boot/EFI/BOOT/BOOTX64.EFI

Install Guide, Chapter 14

< Prev

Next >

Install/Bootloader/tr