The Funtoo Linux project has transitioned to "Hobby Mode" and this wiki is now read-only.
Difference between revisions of "Install/Prepare Disk"
m (Protected "Install/Prepare Disk": open a bug to change this page ([Edit=Allow only administrators] (indefinite) [Move=Allow only administrators] (indefinite))) |
|||
| Line 8: | Line 8: | ||
<!--T:24--> | <!--T:24--> | ||
In this section, you will need to choose a disk format to use for booting and partitioning -- either MBR or UEFI | In this section, you will need to choose a disk format to use for booting and partitioning -- either MBR or UEFI. | ||
MBR is the traditional way of booting a PC. It works by installing executable code on the boot sector of your hard drive, which starts the boot process. | |||
UEFI is the more modern way to boot a PC. It works using a boot loader that is built into your computer. Boot entries are created and stored in your computer's non-volatile memory. | |||
Generally, it's usually safe to pick the legacy MBR method for system disks under 2TB in size and most modern PC systems support MBR as well as UEFI booting. | |||
{{Info|For more information on differences between MBR and UEFI, see our [[Install/Disk Formats|Disk Formats]] page for an overview of each option and the trade-offs.}} | |||
==== But First... ==== <!--T:25--> | ==== But First... ==== <!--T:25--> | ||
Revision as of 16:27, March 21, 2024
Install Guide: Prepare Disk
| Install Guide, Chapter 2 | < Prev | Next > |
In this section, you will need to choose a disk format to use for booting and partitioning -- either MBR or UEFI.
MBR is the traditional way of booting a PC. It works by installing executable code on the boot sector of your hard drive, which starts the boot process.
UEFI is the more modern way to boot a PC. It works using a boot loader that is built into your computer. Boot entries are created and stored in your computer's non-volatile memory.
Generally, it's usually safe to pick the legacy MBR method for system disks under 2TB in size and most modern PC systems support MBR as well as UEFI booting.
But First...
Before doing anything to your disks, make sure you are partitioning the right one. Use the lsblk command to view a list of all block devices on your system, as well as partitions on these block devices:
root # lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 1.8T 0 disk ├─sda1 8:1 0 512M 0 part ├─sda2 8:2 0 8G 0 part [SWAP] └─sda3 8:3 0 1.8T 0 part ├─main-root 254:0 0 500G 0 lvm / └─main-data 254:1 0 1.3T 0 lvm /home
If you're not sure which disks are which, you can use lsblk -o MODEL,NAME,SIZE to show the device models matching the /dev/sd? names.
Make sure you will not be overwriting any important data and that you have chosen the correct /dev/sd? device. Above, you can see that SATA disk sda contains three partitions, sda1, sda2 and sda3, and that sda3 contains LVM volumes. If you are using an NVME disk, then you may see nvme0n1 as your disk, and your partitions (if any exist yet) will be named nvme0n1p1, nvme0n1p2, etc. If you are installing on microSD Card for Raspberry Pi, your disk will likely be mmcblk0 and partitions will have suffixes p1, p2, etc.
Once you've double-checked your target block device and made sure you'll be partitioning the correct disk, proceed to the next step.
| Install Guide, Chapter 2 | < Prev | Next > |